1、沖擊性能試驗
（1）將（安全工具拉力機）安全帽試驗傳感器與安全帽測試儀傳感器接口相接
（2）在未試驗前接通電源，當顯示屏上出現開機“豪泰電氣歡迎你！"畫面后，先后按測試鍵，用方向鍵(↑)(↓)移動光標到“安全帽"后按確認鍵，出現“1#安全帽沖擊" “2#安全帽穿刺"字樣，此時電磁鐵通電產生磁力，將錘頭平面對準電磁鐵下面，使電磁鐵與錘頭中心吸合。用方向鍵(↑)(↓)移動光標選擇 再按確認鍵便進入相應的測試狀態，出現“滴、滴"聲便可落錘測試，（聽聲后5秒內需完成錘頭沖擊），并在數秒后顯示沖擊數據，如該沖擊力小于4.900kN，則試驗通過。如需打印便按打印鍵打印出測試報告。復位退出。當再做下一只安全帽時按測試健開始重復以上步驟即可。
2、耐穿刺性能試驗
將一頂完好的安全帽放在頭模上，電力安全工器具力學性能試驗機（安全工具拉力機）安全帽襯墊與頭模間放置電接觸裝置的一個電極，該電極由鋁片制成，如鋼錐與該電極相接觸，可形成一個閉合回路,在未試驗前接通電源，當顯示屏上出現開機“豪泰電氣歡迎你！"畫面后，用鋼錐從1m高度落下穿刺安全帽頂中心100mm范圍內，先后按測試鍵，用方向鍵(↑)(↓)移動光標到“安全帽"后按確認鍵，出現“1#安全帽沖擊"“2#安全帽穿刺"字樣，此時電磁鐵通電產生磁力，將穿刺錘頭平面對準電磁鐵下面，使電磁鐵與穿刺錘頭中心吸合。用方向鍵(↑)(↓)移動光標選擇 再按確認鍵便進入相應的測試狀態，出現“滴、滴"聲便可落錘測試，（聽聲后5秒內需完成錘頭沖擊），并在數秒后顯示是否穿刺，未穿刺則試驗通過，穿刺自動保存，打印報告。復位退出。當再做下一只安全帽時按測試健開始重復以上步驟即可。
